How to adjust your headlights

How to adjust your headlights

To illuminate your route, you must have high-quality headlights. However, the bulbs are useless if they’re not pointed towards the road correctly, something many vehicle owners fail to remember.

Anyone ever had their headlights blinding them while driving or observed that their headlight is not lighting them precisely in front of them when they’re behind the wheel? Your headlights may be misaligned if you can only see the vegetation on the side of the road or if approaching vehicles are blowing their horns or flashing their high beams at you continuously. Using a screwdriver and a few measures, you can quickly and easily make them fit your needs.

The misalignment of a car’s headlights may be caused by the passage of time or even by changing a single bulb. There’s a chance that this may make it more difficult to see at night, which is a significant safety issue. Unless anything darts onto the road in front of you, you have just seconds to escape an accident while driving 60 mph. Lights that aren’t appropriately aligned may cause you to lose all response time.

The process of adjusting the headlights is simple, but it may be time-consuming to get them precisely right since each vehicle is unique. You’ll be able to accomplish it in your driveway in a couple of minutes with practice and perseverance.

Making some headlights adjustments

To begin, see whether your vehicle is equipped with headlight alignment bubble levels integrated into the dash. For example, Honda’s headlight aim indicator has both vertical and horizontal bubble levels. Headlights typically have them on the top or side. Adjust the aim until the bubble is centred on a level with these. Only vertical or horizontal bubble levels are available on specific models, but there is no apparent alignment indication on the majority of them.

Misaligned lights can reduce reaction time to zero

Misaligned car lights can reduce reaction time to zero

Don’t be concerned if you don’t have one of these features in your vehicle. Make sure your headlights are aligned with your car using a simple, do-it-yourself method.

To begin, choose a level spot to park on and check your car’s level. That necessitates unloading large goods, refuelling the vehicle, and checking the tire pressure on all four wheels. If your car isn’t level, you can’t position your headlights. Also, check whether your suspension is in good functioning condition and not causing your vehicle to lean to one side or the other.

The next step is to locate a blank wall. Turn on your lights and go as near to the wall as you can without damaging the vehicle. The low-beam headlight centres may be found in this manner. One piece of horizontal tape across the centre should mark both locations. Again, run the vertical tape marker across the centre of the low beams at a distance of approximately two feet.

Steps to adjust headlights

Step by step to adjust headlight beam leveling
  1. Level your car
    Start by clearing out the trunk of any unnecessary items. Always follow the manufacturer’s recommendations for tire pressure. To be safe, have someone else drive and make sure the
    tank is half-full. Make sure your headlight aim adjustment wheel is set to zero if you have one.

  2. Position your car
    If you’re parking on flat ground, point the front of your vehicle toward a dark wall or garage door from 10 to 15 feet away. It’s better to park on a paved surface or a flat driveway.
    • Level the shocks by bouncing the vehicle a few times on all four corners.
    • Verify that the suspension is level by measuring the distance from both headlights to the ground.
  3. Turning the headlights on
    If you can avoid it, use dim or no lighting. Tape the headlight beam centre lines horizontally and vertically to the wall or garage door, and then make two T’s in the wall or door.
  4. Make sure the lights are level
    To check whether the two indicated centre lines are equal, use a carpenter’s level. Before you lower another centreline marker to match that height, use a tape measure to establish the size of the lower mark on the wall. There should be no more than 3.5 feet (1.1 m) between these centrelines and the ground.
  5. Back your vehicle up to a wall or garage door that is precisely 25 feet (7.6 m) away
    Don’t make an incorrect assumption about the distance! Check your distance from the wall using a tape measure to make sure it’s correct for you. The headlights should be turned off. Locate the adjustment screws and remove the trim ring around the headlights. While these screws are often located next to the headlight, they may also be hidden from view in the engine compartment. Marking the horizontal and vertical adjusters is essential.

    Always follow the instructions in the owner’s handbook since various manufacturers call for different adjustment distances. As a result, consult your owner’s manual and adhere to the instructions provided there.

    There should be two screws in most automobiles to adjust the headlights: one at the top to adjust vertically and one on the side to adjust horizontally. However, some vehicles have adjustment bolts instead of screws.
  6. Adjust each headlight separately
    Cover one of them while working on and testing the other to avoid confusion due to light leakage. Be sure to have a buddy drive so that you can switch the lights on and off as necessary.
  7. To modify the vertical field, turn the top screw or bolt
    Turning the knob clockwise will increase the lights while doing so counter-clockwise will decrease them.
    After you’ve made any necessary adjustments, turn on your headlights and examine the light pattern on the wall. At its most potent, your laser beam should be just above or slightly below where you drew your tape line.
  8. Turn the side screws or bolts to adjust the horizontal field
    With the right-to-left adjustment, the process is the same as before. The most intense portion of the beam should be located mainly to the right of the vertical line to be used.
  9. Test your alignment on the road
    Make sure your car’s headlights are set correctly by taking it for a spin. Repeat the previous procedures to make any adjustments that were required.

Final words

You can drive safely if your headlights are aimed correctly. Even a non-technical person can

You can drive safely if your headlights are aimed correctly. Even a non-technical person can adjust the headlights at home using this method. You should, however, check your owner’s manual before making any adjustments to your headlights because different manufacturers have different requirements. Also, keep in mind that depending on your car, you may have to adjust your fog lights and high beams separately. These lights can also be aimed by using the same adjusting procedure.

Check out headlight store for more tips and tricks related to adjusting headlights. Hope you’ve learnt something new? Drop a comment now and share with others. 

Like this article? Share it with others!
More on our blog
How to test headlight relay
Car Headlights

How to test headlight relay

Automobile headlight systems are only marginally more sophisticated than your home’s light switches, despite how intricate they may seem. The electrical circuit between your home’s […]

Read More…

Read More »

Table of content

click on the flag to change language please.

Russian spanish German French Italian Arabic Japan Philippines Romanian Moldova Turkey Portuguese Portuguese netherlands swedish vietnamese Finnish Bulgarian Greek